Engineering resource

Motor drive PCBA: power loops and heat paths

A motor drive PCBA needs a layout review that follows current and heat through the complete assembly. A schematic can show the correct connections while leaving a long return path, an inaccessible measurement point or an undefined heat-sink interface. These gaps are especially costly when the board is released for turnkey assembly: the assembler can build the supplied geometry accurately without being able to prove that the geometry meets the motor system’s requirements.

Before release, prepare a marked layout that distinguishes the power path, gate-drive connections, current measurement connections and intended thermal path. Add the actual operating conditions and the mechanical hardware that will be fitted. This article describes the information needed for that review and for an interpretable first build. It does not assign a universal current rating, trace width or via count to motor driver boards.

Describe the operating case before reviewing copper

Give the reviewer more than the motor’s nominal supply voltage. Identify the intended supply range, operating current conditions, switching settings and mechanical duty. Explain which startup, acceleration, braking or stalled conditions are part of the product requirement. The design authority should define the allowed duration and behavior of abnormal conditions. An assembler should not infer those limits from the connector size or from a peak-current number in a semiconductor description.

Identify the motor and cable arrangement used for validation. If several motors are supported, state how the chosen samples represent the intended configurations. Record whether the test supply can accommodate the system’s expected operating behavior, including any energy returned during deceleration where applicable. The electrical test plan must describe its equipment and protective arrangements rather than treating every bench supply as interchangeable.

Carry these conditions into the quotation and release package. The industrial control assembly requirements discussion provides a starting point for defining the project, but the actual motor, enclosure and load conditions belong in the customer’s controlled documents. Without them, “tested at full load” can mean different things to design, manufacturing and the final integrator.

Annotate complete paths, including their returns

On the layout, mark the relevant forward and return paths for each operating state under review. Show where current changes layers and where it passes through connectors, shunts or narrow copper sections. A large polygon elsewhere on the board does not answer whether the critical connection has an avoidable bottleneck. The review should inspect the actual copper geometry after pours are regenerated, not only the schematic net names.

TI’s motor driver layout guide, SLVA959B, revised October 2021, discusses reducing high-current loop inductance through component placement, suitable copper connections and controlled layer transitions. It also treats bypass placement, current sensing and thermal connections as related layout topics. Use its examples with the selected driver’s documentation; their specific geometry is not an automatic release rule for a different stackup or operating condition.

Turn that guidance into a review deliverable: a layer plot with the critical paths highlighted and a short explanation of each intentional transition. Ask the designer to resolve ambiguous return routes and document any compromise imposed by connectors or enclosure dimensions. The goal is not to eliminate every via regardless of context, but to understand where the implementation differs from the intended electrical path.

Check whether late mechanical changes have altered the reviewed geometry. Moving a mounting hole, widening a slot or adding a connector keepout can remove useful copper or force a return path elsewhere. If the layout is edited after the review, identify the affected paths and reopen those checks. A signed review of an earlier copper pour does not cover an unexamined final fabrication file.

Review gate-drive connections as their own circuit

The gate-drive loop deserves a separate annotation from the motor power path. Identify the driver output, any series components, the transistor gate and the associated return connection. Show how the return reaches the driver reference. Where the selected device provides a dedicated connection intended for sensing or gate return, preserve that distinction in the drawing and confirm the manufacturer’s instructions.

Infineon’s EiceDRIVER routing guidance emphasizes loop area, unwanted common impedance and the effect of vias on planes and routing. These are reasons to review the complete connection pair rather than judging only the visible gate trace. The application still determines the appropriate isolation, spacing, device limits and measurement method.

Record the fitted gate network in the BOM, including any options that are intentionally not populated. If tuning during bring-up changes a resistor or adds a damping component, record the board identity and the resulting configuration. Do not transfer a bench modification into production by an informal instruction to “use the values that worked.” Update the released BOM and assembly drawing so the next build reproduces the evaluated circuit.

Keep the current measurement path identifiable

Current sensing is a measurement system within the power system. Mark where the measured voltage is taken and how the connection reaches the amplifier or driver. Identify the shunt footprint and any filtering components. A reviewer should be able to distinguish the load-current path from the voltage-sensing connections, including the intended pickup points, without guessing from a dense image of copper.

For an illustrative calculation, suppose a design uses a five milliohm shunt carrying eight amperes. Ohm’s law gives forty millivolts across the ideal resistance, and the resistive dissipation is 0.32 watts. These numbers are an example, not a recommended design. They help the team see why additional connection voltage or an unsuitable measurement setup could matter, and why the component’s thermal conditions and specified ratings must be reviewed separately.

Write the measurement acceptance criteria in terms the test team can execute. Specify the applied condition, the expected reported quantity, the permitted error and the configuration used. If software converts an analog reading to current, identify the conversion parameters and firmware revision. A correct raw signal combined with an incorrect software scale is still an incorrect system result.

Draw the intended heat path through the assembled product

A thermal drawing should show where heat is intended to leave each significant source and where it ultimately reaches the environment. Include the package-to-board connection, relevant copper layers, any interface material, spreader and enclosure attachment. Mark which items are supplied by the assembler and which are added during final product integration. That ownership boundary determines what an assembly acceptance test can actually verify.

TI’s layout guide discusses the thermal pad, connected copper and thermal vias as parts of the heat path. The practical release question is whether the package-specific land pattern, PCB fabrication details and soldering process support the chosen implementation. Do not choose a via count from a generic photograph or infer thermal performance from copper weight alone. Have the design and manufacturing teams review the real stackup and pad arrangement together.

For a mechanical heat-sink interface, identify the exact material and assembly instructions. Thickness, fitted position, attachment hardware and the approved tightening method should be available to the person doing the work. If the interface depends on compression, the mechanical design must establish the intended assembled condition. The operator should not be asked to determine it by feel or by an unrelated example drawing.

Decide how the finished interface will be checked. A visible presence check can establish that material was fitted, but may not establish contact over the required area. A temperature test can provide system evidence, but only for its stated configuration and conditions. Choose complementary checks based on the actual failure concern rather than treating one inspection as proof of every aspect of the heat path.

Resolve manufacturing details before the first build

Review package handling, orientation marks and inspection access for the power devices and driver. Where joints or pads are hidden, define the intended inspection evidence and acceptance authority. Discuss the solder paste and stencil approach with the assembler using the package documentation and actual board geometry. A thermal connection that exists in CAD still needs a process capable of forming the intended joint.

Make the fabrication notes consistent with the assembly plan. If the design relies on filled, capped or otherwise treated vias, state the required construction rather than using a vague note such as “thermal vias.” Obtain clarification before fabrication when the drawing and quotation differ. The chosen via construction can affect both assembly behavior and cost, so it should not become an undocumented substitution at purchasing.

Separate provisional process settings from released requirements. During the pilot, manufacturing may adjust a program or profile within the approved process approach. Capture the final settings and the evidence used to accept them. If the proposed solution changes the board design or component requirements, route it back to engineering instead of hiding a product change inside the production setup record.

Prepare measurements that can distinguish faults

The first-build plan should identify observation points before power is applied. Mark appropriate access for the gate-drive signals, relevant supply behavior, current measurement and temperature observations. Choose probes and connections suitable for the signal and voltage involved. Poor access can encourage a measurement arrangement that changes the behavior being investigated or makes comparisons between samples unreliable.

Agree which assembly testing options are included and which design validation activities remain with the engineering team. A basic production functional check may establish that communication and commanded motion occur, while a detailed switching or thermal investigation requires different instrumentation and conditions. Document that distinction in the report so that a manufacturing pass is not mistaken for complete product qualification.

When a board behaves unexpectedly, preserve the original configuration and observation before changing several settings. Log the operating mode, firmware, fitted components, motor, cable and test equipment. Change one relevant variable at a time where practical, and record what changed. If multiple changes are necessary, identify the final configuration without claiming that each individual change has been proven responsible.

Release the build with an explicit evidence package

Finish the review with the annotated paths, final fabrication and assembly files, approved material list, mechanical interface instructions and test plan. Record unresolved items with an owner and a decision date. An unresolved thermal interface or measurement access issue should have a visible disposition rather than disappearing when the purchase order is placed.

Use the release-file readiness checklist to reconcile the supplied revisions, then add the motor-specific documents described here. For the next build, compare the final implemented configuration with the one actually tested. This preserves the connection between electrical intent, manufactured geometry and measured behavior, giving the production team a repeatable basis for assembly rather than a collection of assumptions.

Your next build,
clearly scoped.
Get a Quote ↗